After spending some time examining the PT1911 and assessing its features, I decided that it was a well-designed pistol. OK. It looks good and has some great features. How does it shoot?
Since this is a 1911 and should be able to handle anything, I took it straight to the range right out of the box. I didn't clean it or give it an extra oiling; I just took it out to the range and shot it.
Initially, I ran 230-grain full-metal-jacket ammunition through the PT1911, just to ensure that it was reliable out of the box. I fired more than 100 rounds, and there were no failures to fire, feed, or extract. It was boringly reliable.
After running factory hardball, I figured a good test for the PT1911 would be a mixed bag of ammunition, all reloads. This mix included 230-grain lead round nose, 200-grain lead semi-wadcutters, and 155-grain lead semi-wadcutters. The 155-grain bullets tend to give most factory pistols fits, but the PT1911 never missed a beat and just kept on shooting.
By the time I was done with the pistol's initial testing, I had put more than 500 rounds through it, and it performed remarkably. There wasn't one failure to feed with the exception of a lead reload where the bullet was improperly seated over the lip of the brass. This made for an extra wide .45-caliber bullet that wouldn't fit in the chamber. This is more the author's problem of not paying attention when loading ammunition, not the PT1911's inability to feed it.
The next time out I fed the PT1911 a variety of factory-produced duty and practice ammunition. The ammo selection included 230-grain JHPS from Black Hills, 230-grain Winchester SXTs, 230-grain Gold Sabers from Remington, 230-grain Federal Hi-Shok HPs, 185-grain XTPs from Hornady; and a mix of 230-grain FMJs from Federal, Winchester, Wolf, and UMC. The PT1911 had zero failures to feed, fire, and extract during the firing of more than 500 rounds. And that was with a dirty gun. I hadn't cleaned it after my previous trip to the range.
From a Rest (Sort of)
After firing more than a thousand rounds to test the reliability of the PT1911, I decided that it was time to see how well this $700 pistol can shoot. Since I don't carry a rest on the job, I opted for a field expedient rest: my range bag. This has served me well for nearly a decade, and I was certain it would again.
I loaded the pistol to its capacity of nine (8 plus 1) and fired it supported off my range bag rest at targets set 20 yards down range. The PT1911 proved to be quite accurate, keeping nine-shot groups under three-and-a-half inches.
Now, you may say, "Three-plus inches? That's not that good." But bear in mind that this is nine rounds, and each one of them is nearly half an inch in diameter. Many of the groups had clusters of four and five rounds with a few rounds opening the group up. I felt this was pretty good for my late-forty-something eyes. I am certain a younger, more talented shooter could produce sub-two-inch groups with the PT1911.
After all this shooting, I figured it was time to finally clean the PT1911. Here's the drill.
First, make sure that the pistol is empty. Next, using a bushing wrench—or base of the magazine if you are old fashioned like me—rotate the barrel bushing to the left, and remove the recoil spring plug and recoil spring. Now push the slide to the rear until the slide stop can be removed through the small u-notch in the slide, pull out the slide stop, remove the slide, rotate the barrel bushing to the other side of the slide, and remove the bushing and barrel.
The pistol is now disassembled for cleaning. Use your favorite cleaner and lube on the PT1911 and simply reverse the procedure to reassemble.
After shooting the PT1911 for the past few months, I am pleased with it. The only issues I have with this gun are that the grips are too thin for my big hands. To compensate, I have installed standard thickness grips. I also prefer an arched mainspring housing over the flat one on the PT1911. An arched housing simply makes the pistol fit my hand better; and I have installed one for that reason. These are purely personal preferences and do not change my view of the PT1911 out of the box.
Overall, I am truly impressed with Taurus' PT1911. It shoots well, it looks good, all the safeties function properly, and it is affordably priced. So if you are looking for a 1911 for duty or personal use, I'd recommend that you look at the Taurus PT1911.
Taurus is working on light rail versions and alloy frame versions of the PT1911. They should be available late this year or early in 2008.
Scott Smith is a disabled veteran who served as an active-duty Army MP and in the U.S. Air Force Reserve and Air National Guard as a security policeman. He is a contributing editor to POLICE.